Top 10 common forklift accidents ， forklift operation should pay attention to these issues ！.

Do not ignore the forklift at the workplace. If the procedure is not good, there will be severe mishaps in mins, and there are lots of crashes entailing forklifts.

Instance 1: The forklift freight obstructed the vehicle driver's view, and the individual ahead can not be located, causing a moving mishap.
Situation 2: In order to preserve the balance of the forklift when lifting heavy items, the staff members utilized their body weight as the weight, which nearly triggered casualties.
Situation 3: The width of the forklift cargo goes beyond the allowed size of the path and hangs on the roadside shelf, which virtually creates an mishap.
Situation 4: Forklift is speeding and surrender throughout a turn.
Instance 5: The forklift motorist did not observe the pedestrian, and the pedestrian did not notice the forklift.
Instance 6: The forklift lifts the personnel illegally, the forklift driver does not wear the safety belt, the forklift lifter falls and the vehicle driver is squashed when the forklift rolls over.
Situation 7: The forklift motorist did not wear a safety belt and fell from the car when it rolled over and was squashed.
Forklift operation should pay attention to these issues ：.

Begin.
1. Before beginning, observe the surroundings, and after confirming that there are no barriers that impede the safety of driving, beep the horn first and then start.
2. For lorries with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) scale have to be secure before starting.
3. When the forklift begins with a lots, the vehicle driver should first confirm that the lots is stable and reputable.
4. The begin must be slow and stable.

Driving.
1. When driving, the elevation in between the bottom end of the fork and the ground should be kept at 300mm-400mm, and the pole needs to be tilted backwards. .
2. Do not raise the fork too expensive when driving. When entering and leaving the job website or while driving, beware that there will be no barriers overhead. When the tons is traveling, the fork needs to not be raised too expensive, which will certainly impact the security of the forklift. .
3. After dumping, the fork needs to be lowered to the typical driving position prior to driving. .
4. When turning, if there are pedestrians or lorries close by, the driving signal ought to be provided first. High-speed sharp turns are banned. High-speed sharp turns will cause the car to shed lateral security and tip over. .
5. When the forklift is downhill, it is purely restricted to turn off the fire and slide, and it is prohibited to brake unexpectedly while driving with lots unless there are unique circumstances.
6. When the forklift is running, it should comply with the web traffic rules in the manufacturing facility and need to keep a certain safety distance from the car ahead. .
7. When the forklift is running, the tons needs to be in the lowest placement that does not prevent the driving, and the gantry should be correctly slanted back. The lots shall not be raised except when piling or filling. .
8. The elevation of the load must not obstruct the motorist's view. In special circumstances, when the item influences the forward vision, drive at a low rate when reversing.
9. It is prohibited to switch on the ramp, nor to drive throughout the ramp. .
10. The risk-free driving rate of the forklift in the factory location is 5 km/h, and it needs to drive safely at a reduced rate when entering the production workshop area. .
11. When the forklift is lifted, lifted or driven, it is forbidden for employees to base on the fork to hold products and play a balancing duty. .
12. If issues are discovered, they will be fixed and reported in a timely manner, and they will certainly never ever run with diseases or conceal them.

filling and discharging.
1. When fork-loading items, the range between both forks must be changed as required to make the tons of the two forks well balanced and not skewed, and one side of the thing must be against the shelf. .
2. It is prohibited to collaborate with a single fork or use a fork top or draw. In special conditions, security indication should be established to remind bordering pedestrians. .
3. In the process of packing and dumping products, the forklift must be braked with the brake. .
4. The rate of the car need to be sluggish and steady. Beware not to roll the wheels on the dunnage, so as not to extend the rolled items and injure people. .
5. When making use of a fork to Stand-on Electric Pallet Stacker fork the goods, the fork ought to be as deep as feasible under the load, and it ought to be kept in mind that the fork suggestion must not touch other products or things. The load must be maintained with minimal back tilt of the gantry to ensure that the lots does not slide in reverse. The pole can be tilted ahead a little when the lots is lowered to enable very easy placement of the load and removal of the forks. .
6. It is restricted to fork goods at high speed and hit tough things with the fork head. .
7. When the forklift is working, it is prohibited for individuals to loaf the fork, so regarding stay clear of the collapse of the goods and injure people. .
8. Overwhelming is forbidden, and it is banned to use forks to lift workers to participate in high-altitude procedures to stay clear of high-altitude dropping crashes. .
9. It is not permitted to use the brake inertia to slip, put, round or roll objects. .
10. It is not allowed to use forks to choose, turn pallet discharge.

Leaving .
1. It is prohibited to leave the forklift when the products on the fork impend. Prior to leaving the forklift, you need to dump the goods or reduced the fork structure.
2. Draw the hand brake take care of to dead or dispirit the hand brake button.
3. The engine is shut off and the power is removed. (Except for special situations, such as the motorist does not leave the car's line of vision and does not surpass 1 minute).
4. Remove the key. .

Forklift Operation Precautions.
1. Prior to and after the forklift procedure, the look must be inspected, and fuel, lubing oil and air conditioning water must be included.
2. Inspect the safety performance of beginning, running and braking.
3. Check whether the lights and horn signals are complete and reliable.
4. Throughout the operation of the forklift, check whether the stress and temperature level are typical.
5. After the forklift is running, the external leak must likewise be checked and the seals need to be replaced in time.

Forklift Safety Operation Specifications.
1. You should check prior to leaving the auto;.
2. When you come across someone before you throughout driving, you should send out a signal at a distance of 5 m;.
3. The driving speed in the factory does not surpass 5 km/h;.
4. When driving, the low point of the freight ought to be 0.3 m ~ 0.4 m above the ground;.
5. The transforming ought to not be also sharp to avoid the tendency of " complimentary turning";.
6. Adding and down the slope needs to be sluggish and consistent, and no switching on the incline is enabled.
7. Do not drive throughout the gradient. When the slope is higher than 10%, the vehicle must be driven backwards when declining;.
8. When the forklift personnel bring the goods and move forward, if they come across large or heavy items and go to the motorist's line of sight, they must take the reversing exercise
.
The "Eight Prohibitions" need to be followed in the procedure.
1. Solitary fork operation is not allowed.
2. It is not enabled to raise the goods for long distance driving.
3. It is not enabled to grab the goods by turning over the pallet with the fork.
4. It is not enabled to straight shovel chemicals, flammables and various other dangerous chemicals with forks.
5. It is not permitted to make use of inertia force to get the goods.
6. It is not permitted to use braking force to expatriation round or easy-to-roll things.
7. It is not allowed to bring people to service the pallet or fork, and it is purely restricted to stand under the fork after the fork is raised.
8. Do not drive laterally on slopes
.
Auto parking is not permitted under the following conditions.
1. Curves, slim roadways, train crossings;.
2. Areas with a longitudinal incline greater than 5%.
3. When there is an obstacle on one side of the road, the Stand-on Electric Pallet Stacker opposite side of the area with the exact same size as the barrier need to be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844